Engine Block Operations

*All Prices Are Subject To Change

Boring, Sleeving, and Honing:
(NOTE: to bore more than .060) $12.00

bore slant deck blocks $36.00
bore 1 cylinder $52.00
bore 2 cylinders $51.00
bore 4 cylinder blocks $97.00
bore 1 cylinder - 2 cycle $52.00
bore 2 cylinders - 2 cycle (Harley) $54.00
bore 1 cylinder - Aluminum $53.00
bore & sleeve 4 cylinder Honda cycle (for big bore kit) $90.00
bore or hone 2 cylinder Onan (ck. BF) Aluminum $51.00
bore 2 cycle Blind hole (boat motors include. Chamfer ) $120.00
bore V4 -65, Wisconsin V4 $51.00
bore VW cases for big bore kit $38.00
bore VW heads for big bore kit $50.00
cut counter bore on 6 cylinder Cummins block to adjust $41.00
bore 4 cylinder motorcycle slant $151.00

Heavy Truck and Equipment Boring:

bore to 4 1/2" diameter $32.00
bore from 4 1/2" to 5" diameter $41.00
bore over 5" $16.00
bore 172 Ford 4 Cylinder Diesel $32.00
bore Ford Tractor - 4.2 & 4.4 - dirty $42.00
bore Ford Tractor - 4.2 & 4.4 - clean $38.00
bore 478, 549H, & V8 Gas International $58.00
bore 534 Ford Angle Top Block $58.00
bore 1160, 3208 Cat. diesel V8 $53.00
bore 2 cylinder JD, Cummins, Etc. $157.00

Cylinder Sleeving (Dry):

up to 4 1/2" $97.00
from 4 1/2" up $157.00
John Deere - 2 cylinder (5 1/2" x 14 1/2") $289.00
Chrome 2 cylinder jug (no cutting of ports) $171.00
F-162 Continental $97.00
Sleeve 534 Ford (angle top block) $171.00
Install 8 sleeves in Big Block Ford Truck V8 $467.00
Install 8 sleeve in 534 Ford Truck $744.00
Bore and Sleeve Truck Hub for Race and Seal $135.00

Remove & Replace Sleeves:

Ford Tractor and 4 cylinder Datson Diesel $32.00
International Red Diamond and Similar $58.00
Wet Sleeves $40.00
Hone and Sleeve 71 series GMC diesel $45.00
Ford Tractor 8N .090 wall sleeves (including boring) $66.00
Bore and Fit 71 series GMC $66.00
6 cylinder MACK 711 R&R Sleeves $67.00
Bore I.H. Farmall M to 281 for big bore kit $78.00
53 series Detroit Diesel $45.00
Cummins $42.00
4clinder Perkins Diesel - 3 1/8" bore - dry not flanged sleeve, set height $62.00

Cylinder Honing:

Hone Heavy Truck and Equipment $29.00
Hone to clean up $14.00
Ridge Ream $16.00
Deglaze Cylinders $13.00
Hone 2 cylinder - cast iron $25.00
Hone 2 cylinder - Chrome $36.00
Ridge Ream and Hone $20.00
Special Hone Passenger Blocks $29.00

Line Boring:

V8 passenger and light truck $206.00
Allis Chalmers 6 cylinder 516 C1 7 main $405.00
Buick V6 $181.00
CAT. 1160, V8, 3208 $504.00
Cummins 903 V8 $606.00
Cummins NH 6 cylinder $658.00
Detroit 8V-7, 8V-92 $460.00
Detroit 6 cylinder 71 $498.00
Saddle Kit inst. V-8-71 (92 Detroit Diesel) $779.00
Saddle Kit inst. V-6-71 (92 Detroit Diesel) $765.00
GMC V6 gas $277.00
John Deere bore .060 under main brg to fit crank $58.00
John Deere 4030 (LINE HONE) $405.00
VW Block $120.00
Minn. Moline V-302, 4 cylinder $405.00
IH Gas 478, 549 $405.00
Back Hoe swing post $734.00

Check Line Bore:

8V-71 Detroit Diesel $97.00
V8 passenger and light truck $50.00
6 cylinder passenger and light truck $58.00
Mack END T675 $120.00
Buick V6 $50.00